Louvered Screens
Our Soleo profiles are the slats behind a louvered privacy screen made for exterior use: an anodized aluminum core under a sanded wood-composite skin, tested non-combustible to ASTM E136.
A row of slats that edits what passes through.
A louvered screen is a set of parallel slats fixed between supports, with open gaps between them. The gaps pass air and daylight while the slats interrupt direct sight lines, which is why one arrangement can work as a privacy barrier, a shading layer or a decorative facade skin.
We supply the slats as Soleo profiles: an anodized aluminum core, hot co-extruded with a wood and polypropylene composite skin that is sanded to bring out natural grain. The slats can run vertical or horizontal depending on the design, and a range of 33 profiles runs from fine, closely spaced slats to broad fins, planks and square posts.
Aluminum core
Anodized A6063S-T5 alloy inside every slat.
Sanded composite skin
Natural grain, sanded rather than printed.
Non-combustible
Tested to ASTM E136 (appendix).
Wide range
Soleo, Planeo, Careo and Diameo profiles.
From extrusion to a finished screen.
Each slat is built in a factory and finished on site. The factory sets the strength and surface; the assembly details set how the screen ages.
How the slat is made: an anodized aluminum alloy A6063S-T5 core is hot co-extruded with a wood and polypropylene composite skin, with an olefin resin bonding layer between them, and the surface is then sanded. The aluminum supplies the structure; the skin supplies the grain and color. The flame retardant in the skin is non-halogenated.
Steps to build louvered privacy screen assemblies: fix each slat to its supports with InPull nuts (M6–M12), blind nuts, flange bolts or self-tapping screws driven through the thicker aluminum walls. Pre-drill holes 2–4 mm wider than the bolt shaft and fit washers so the slat can expand; nails are not used. Straight and corner connectors join lengths, and glued end caps close the open ends, with their four weep openings left clear.
Two featured profiles, two kinds of louver.
Soleo 6008 and Soleo 6010 are our two most-specified profiles, so they are the two detailed on this page. They are examples only: every one of the 33 profiles in the full range further down can be used for louvers. The two share the same construction and colors, and differ in width, depth and the visual weight each slat carries.
| Parameter | Soleo 6008 | Soleo 6010 |
|---|---|---|
| Section | 2 × 1¼ in. (50 × 30 mm) | 5⅛ × 2⅛ in. (128 × 53 mm) |
| Weight | 0.57 lb/ft | 1.55 lb/ft |
| Visual character | Fine slat with a close, rhythmic repeat | Deep blade with strong shadow lines |
| Suited to | Tightly spaced decorative screens, louvered facade accents, pergolas | Deeper louver blades, longer spans between supports, sunshades and fins |
| Shared by both | Same aluminum core, same sanded skin, same colors, same fire classification, same 10-year warranty. | |
Louvered screen panels are assembled from these slats on site, so the profile choice fixes the look before any spacing is set. A narrow section reads as texture from a distance; a wide section reads as individual blades. Closer spacing narrows the view through the screen, and wider spacing lets in more light and air.
Some projects combine sections, with one profile for the main field and another as an accent or a secondary layer. Governor’s Plaza in Maryland uses Soleo 6008 and 6010 together, and the BJC Outpatient Center in Missouri uses Soleo 6008 and 6033.
One slat, many ways to use it.
Privacy, shade, decoration or an overhead feature: the same Soleo slat is specified for each, so the finish stays consistent across a whole project.
Get Your SamplesThe profiles: Soleo 6008 and Soleo 6010
Our two most-specified hybrid aluminum battens, shown as examples. Every profile in the full range below can be used for louvers.

Soleo 6008 · 2 × 1¼ in.
| Section | 2″ × 1¼” | 50 × 30mm |
| Weight | 0.57 lb/ft |
| Standard length | 9 ft 10 in | 3.0m |
| Custom lengths | 7 ft – 19’8″ |
| Fire rating | Non-combustible, ASTM E136 (appendix) |
| Core | Anodized aluminum alloy A6063S-T5 |
| Skin | Wood / polypropylene composite, sanded |
| Warranty | 10-year limited, non-prorated |

Soleo 6010 · 5⅛ × 2⅛ in.
| Section | 5⅛” × 2⅛” | 128 × 53mm |
| Weight | 1.55 lb/ft |
| Standard length | 9 ft 10 in | 3.0m |
| Custom lengths | 7 ft – 19’8″ |
| Fire rating | Non-combustible, ASTM E136 (appendix) |
| Core | Anodized aluminum alloy A6063S-T5 |
| Skin | Wood / polypropylene composite, sanded |
| Warranty | 10-year limited, non-prorated |
Soleo 6008 and 6010 are stocked in the USA: no minimum in Teak and Rosewood. *1,000 lineal ft minimum. **Non-standard color, 90-day lead time, 5,000 lineal ft minimum.
33 profiles in four families.
Every Architectural Elements profile can be used for louvers, as well as privacy screens, sunshades, decorative screens and brise-soleil. Each is a hot co-extrusion of anodized aluminum and wood composite that meets the IBC 2018 703.5.2 definition of composite noncombustible, offered in Teak, Rosewood, Ebony and Moleskin. Soleo 6008 and 6010 are shown in detail above; the tiles below cover every Soleo batten, Planeo fin and plank, Careo square post and Diameo diamond fin we carry.
Soleo
1¾ × 1 in. Soleo 6027Slimmest
1⅝ × 1¼ in. Soleo 6008Batten
2 × 1¼ in. Soleo 6029Medium-Width
2⅜ × 1¼ in. Soleo 6026Square-Profile
2⅜ × 1⅝ in. Soleo 6011Broad-Profile
2¾ × 1⅝ in. Soleo 6030Plank-Style
3⅛ × 1¼ in. Soleo 6017Multi-Chamber
3⅝ × 1⅝ in. Soleo 6036Ultra-Flat Slat
4 × ⅝ in. Soleo 6009Wide
4 × 1¼ in. Soleo 6034Deep
4⅛ × 2⅛ in. Soleo 6031Wide-Slim
5 × 1⅛ in. Soleo 6010Deep
5⅛ × 2⅛ in. Soleo 6038Wide-Flat
5¾ × ⅞ in. Soleo 6024Wide
5¾ × 1¼ in. Soleo 6040Wide-Deep
6 × 2 in. Soleo 6050Large
6 × 4 in. Soleo 6033Wide-Format
7⅞ × 1⅜ in.
Planeo
5¾ × 1¼ in. Planeo 4044Fin (Deep)
6⅞ × 3⅜ in. Planeo 4123Plank (Slim Wide)
11⅜ × 1¼ in. Planeo 4048Plank (Broad Wide)
11¾ × 2 in. Planeo 4061Plank (Deep)
11¾ × 4 in. Planeo 4046Fin (Wide Large-Scale)
13¾ × 4¼ in. Planeo 4062Plank (Extra-Wide)
17¾ × 4 in.
Careo
1¾ × 1¾ in. Careo 7031Square Post
1¾ × 1¾ in. Careo 7011Square Post
2⅛ × 2⅛ in. Careo 7035Square Post
3⅜ × 3⅜ in. Careo 7014Square Post
3½ × 3½ in. Careo 7016Square Post
4¾ × 4¾ in.
Diameo
Profiles drawn to the same scale, simplified outlines for proportion only. Section sizes in inches.
Standard length is 9 ft 10 in for Soleo, Planeo 4010, Careo and Diameo 2018, with custom lengths up to 19 ft 8 in (Soleo 6026 up to 18 ft). The other Planeo profiles and Diameo 2023 are made to custom length, up to 26 ft. Planeo boards are built from hybrid profiles bolted together internally, so they can be shortened only at the 2 in. ends beyond the end bolts. Qualita decking is a separate product line and is not listed here.
See the Full Architectural Elements RangeSpecify with confidence
Documentation for the Soleo profiles and the architectural elements built around them.
How Soleo Slats Compare with Other Louver Materials
An aluminum-core composite slat against the five materials most often considered for louvers.
| Parameter | Geolam Soleo (Aluminum-Core Composite) | Solid Wood Slats | Bare Aluminum Slats | Solid WPC Slats | Terracotta Baguettes | Rice Hull / PVC Composite |
|---|---|---|---|---|---|---|
| Construction | ✓ Anodized aluminum core with a co-extruded wood-composite skin. | Solid timber throughout. | Aluminum throughout, with a coated or anodized surface. | Wood fiber and plastic, no metal core. | Fired clay sections. | Rice hulls bound in PVC. |
| Fire Classification | ✓ Non-combustible, ASTM E136; Class A, ASTM E84. | ✗ Combustible unless treated. | ✓ Non-combustible. | ✗ Class A, but not non-combustible. | ✓ Non-combustible. | ✗ Class A, but not non-combustible. |
| Appearance | ✓ Sanded natural grain with color variation. | ✓ Genuine grain, varies by species and cut. | Metallic; a wood look needs a printed or sublimated coating. | Brushed composite surface. | Clay finish, glazed or natural; no wood grain. | Needs a finish coat for color. |
| Maintenance | ✓ Soap and water or power washing; no staining or sealing cycle. | ✗ Periodic staining or sealing to hold its color. | Depends on the coating. | Follow the manufacturer’s care guide. | ✓ Low. | ✗ Finish needs periodic re-coating. |
| Weight & Length | ✓ 0.57 lb/ft (Soleo 6008) to 1.55 lb/ft (Soleo 6010); custom lengths up to 19 ft 8 in. | Typically 8–12 ft lengths. | Typically 12–24 ft stock lengths. | 12 ft standard lengths. | ✗ Around 8 lb/ft; pieces up to about 6 ft. | 12 ft standard lengths. |
| Warranty | ✓ 10-year, non-prorated. | Varies by supplier and species. | Varies by supplier and coating. | Often around 5 years. | ✓ Often 30 years. | Material warranty; finish often not covered. |
General category patterns from Geolam’s material comparison charts; individual products vary by manufacturer.
Download the Full Materials Comparison GuideWhat makes this the right louvered screen material.
When specifiers weigh louvered screen material options, the decision usually comes down to fire performance, aesthetic, durability and upkeep. A Soleo slat answers all four: an aluminum core for the non-combustible classification, a sanded composite skin for the grain, tested weathering for long-term durability, and a surface that needs no recoating.
The wood fiber is dried to 0% moisture before extrusion, and the finished profile carries 70–80% recycled content and is fully recyclable. The profiles are certified under the Japan Environmental Association’s Eco-Mark and made to ISO 9001/14001 standards.
A louvered screen wall shows every flaw, hundreds of times.
A louvered screen wall repeats one slat across the whole elevation, and every slat is exposed on several faces to sun, rain and cleaning. A small difference in color or finish between slats shows up as a pattern, so consistency matters more here than on a flat panel.
Because the sanded skin is the finish rather than a coating applied over it, there is no paint layer to chip along edges, and the aluminum core gives each slat its structure. That combination is why the profiles appear on offices, a museum and a public parking structure in our project gallery.
Keeping an open-slat screen clean.
Open slats catch dust, pollen and leaves in the gaps, so cleaning is the main task. Soap and water handles routine cleaning, and power washing is fine: it does not affect the warranty. There is no staining, sealing or repainting cycle, because the sanded composite surface is the finish itself.
One detail is specific to louvers: the end caps have four weep openings that let moisture drain, and they should stay unblocked. The 10-year warranty is non-prorated.
Long slats move with the temperature.
Soleo’s finish is weathering-tested under DIN ISO 16474-2 and to 5,000 hours under JIS A 1415, and salt-spray tested under DIN EN ISO 9227.
Movement is a design input on a long screen. The linear thermal expansion of our profiles matches aluminum, which works out to about 0.92 mm per meter across a 40°C temperature swing. That is why the installation guide specifies oversized pre-drilled holes and washers: the slat slides slightly at each fixing instead of binding.
Who stands behind these profiles?
We are Geolam, Inc., based in Toronto, Ontario, and the exclusive North American importer and distributor of Geolam® architectural building products manufactured in Japan. The hot co-extrusion process behind the Soleo profiles bonds wood-composite and aluminum in one continuous run.
Soleo 6008, 6010, 6031 and 6033 are kept in stock in the USA in Teak and Rosewood with no minimum order, and lengths can be ordered between 7 ft and 19 ft 8 in. We are also SAM.gov registered for U.S. government work.
Certifications & performance attributes
Natural grain
Each slat is sanded, not printed, so the texture is real.
Non-combustible
An aluminum core classified under ASTM E136.
Open-slat design
Narrow to wide sections, vertical or horizontal.
10-year warranty
Non-prorated, across the whole profile.
Soleo profiles on built projects
A louvered screen and four decorative screens, from our project gallery.
BJC Outpatient Center — MissouriSoleo 6008 and 6033, Teak and Rosewood — louvered screen
Governor’s Plaza — MarylandSoleo 6008 and 6010, Teak — decorative screen
Grammy Museum — MississippiSoleo 6010, Rosewood — decorative screen
Rosecrans Ave — CaliforniaSoleo 6030 and 6031, Teak — decorative screen
Centene Office Building — MissouriSoleo 6033, Teak — decorative screen
These five Soleo projects span Missouri, Maryland, Mississippi and California. Browse the full gallery for more named commercial installations across North America.
See All Projects in the GalleryStandard finishes & sections
Soleo 6008 and 6010 in six wood-look tones.

Teak
Warm, golden hardwood tone
Rosewood
Deep reddish hardwood tone
Moleskin*
Cool, driftwood grey
Ebony*
Near-black, low-sheen finish
Carbon**
Deep matte black
Bilinga**
Rich amber-brown hardwood tone*1,000 lineal ft minimum on Soleo 6008, 6010, 6031 and 6033; every other profile has a 1,000 lineal ft minimum in any color. **Non-standard color, 90-day lead time, 5,000 lineal ft minimum. Custom colors: 6,000 lineal ft minimum.
Finish choice sets the character of a screen as much as the profile does. Soleo 6008, 6010, 6031 and 6033 are stocked in the USA in Teak and Rosewood with no minimum order, which suits smaller screens and fast programs; in Moleskin and Ebony they ship against a 1,000 lineal foot minimum. Every other profile in the range has a 1,000 lineal foot minimum in any standard color.
Carbon and Bilinga are special-order colors, and custom colors start at 6,000 lineal feet. The grain, sanding and shading can vary between production runs, so request a physical sample before committing a full screen.
Request Physical Samples
The two featured sections, side by side
Soleo 6008 and Soleo 6010 drawn to the same scale, so the difference in width and depth is easy to judge.
The dark band in each outline marks the aluminum core and the colored band the composite skin. The drawings are simplified to show proportion only; use the datasheets for the actual profile geometry.
What affects louvered screen cost?
The material is only part of the number. Here is what moves the total.
Get a project-specific number
Send your screen dimensions, preferred slat spacing and location to one of our representatives for an accurate quote.
Request a Quote Find Your Local RepWhat architects say
Architects on specifying Geolam Architectural Elements.
“Not only is Geolam a great product but it also has wonderful technical support! The reps and technical support helped us design and detail the product as it was intended to be used and were also helpful and encouraged us to push the boundaries and explore some design possibilities to use the product in ways not originally envisioned.”
“It’s particularly good for spaced out slat applications, where the homogenous nature of the material is a desired quality.”
“Architectural Elements were chosen for their low maintenance composite wood finish, and clean aesthetic with warm wood tones that married perfectly with our material palette.”
Louvered screens, common questions
What is a louvered screen?
A louvered screen is a series of parallel slats fixed between supports, with gaps between them. Air and light pass through the gaps, while the angle and spacing of the slats limit direct views. Architects use the arrangement for privacy, for shade and as a decorative layer on a facade.
What is the best louvered screen material for outdoor use?
It depends on fire code, appearance and upkeep. Solid wood gives genuine grain but needs regular staining or sealing and is combustible. Bare aluminum is non-combustible and durable but reads as metal unless it is coated. Geolam Soleo combines the two: an anodized aluminum core under a sanded wood-composite skin, tested non-combustible under ASTM E136 and cleaned with soap and water.
How do I build a louvered privacy screen?
Set the supports first, then fasten each Soleo slat to them using the fixings in our installation guide: InPull nuts, blind nuts, flange bolts, or self-tapping screws through the thicker aluminum walls. Pre-drill holes 2–4 mm wider than the bolt shaft and fit washers so the slat can expand. Join lengths or turn corners with connectors, cut with an aluminum chip saw, and glue end caps on the open ends. Our guide also links a louver assembly video.
How far apart should louvered screen slats be?
Spacing is a design decision rather than a fixed rule. Closer slats narrow the view and reduce light, while wider gaps open the view and pass more air. Soleo 6008 suits a tight rhythm and the deeper Soleo 6010 suits a wider pitch with stronger shadows. Mock up the layout with physical samples before fixing the spacing.
Can the slats run vertical or horizontal?
Yes. Vertical slats emphasize height and horizontal slats emphasize width, and either direction is a design choice. Soleo 6008 and Soleo 6010 both work for screens and facade accents, so the orientation can follow the building’s lines.
How are louvered screen panels assembled?
Louvered screen panels are made by fastening parallel slats to supports at a chosen spacing. We supply the profiles, connectors and end caps, so the size of each panel comes from the design and from the available lengths: 9 ft 10 in as standard, or custom lengths from 7 ft to 19 ft 8 in.
Can a louvered screen wall be used on a commercial building?
Yes. Soleo profiles are on offices, a school and public buildings, including the Centene Office Building, the BJC Outpatient Center and the City of Naples 1st Avenue Parking Garage. Confirm the fire requirements with the local authority having jurisdiction before specifying.
Do you make a folding louvered screen?
No. We supply Soleo profiles for fixed architectural screens, such as privacy screens, facade louvers and sunshades. A hinged, freestanding divider is a furniture product that needs its own frame and hardware.
What does non-combustible mean for a slat with a composite skin?
Soleo is a composite: an aluminum core under a wood and polypropylene skin that contains a non-halogenated flame retardant. The assembly is rated Class A under ASTM E84, and non-combustible under ASTM E136, a stricter test, and meets the IBC 2018 703.5.2 definition of composite noncombustible. Ask for the test report when you submit the product.
Do louvered screens need painting or staining?
Not with Soleo. The sanded composite surface is the finish, so there is no coating to renew. Routine care is soap and water, power washing is fine and does not affect the warranty, and surface damage can be sanded out.
Can Soleo slats be cut or bent on site?
Cutting needs an aluminum-cutting chip saw at a maximum of 2 meters per minute; grinders and chainsaws can deform, crack or peel the product. Bending should not be done at 20°C or lower, and the product should not exceed 60°C during bending. Avoid oil or liquids on the work. Planeo boards are built from profiles bolted together inside, so shorten them only at the 2 in. ends past the end bolts.
Do the slats expand in hot weather?
Yes, at the same rate as aluminum. A 40°C temperature difference lengthens a profile by 0.92 mm per meter, or roughly 2.8 mm on a standard 3 m slat. Oversized pre-drilled holes and washers give the slat room to move.
Which colors are available, and are there minimums?
Teak, Rosewood, Moleskin and Ebony are the standard colors. Soleo 6008, 6010, 6031 and 6033 are stocked in the USA with no minimum order in Teak and Rosewood, and a 1,000 lineal foot minimum in Moleskin and Ebony. Every other profile has a 1,000 lineal foot minimum in any standard color. Carbon and Bilinga are non-standard colors with a 90-day lead time and a 5,000 lineal foot minimum, and custom colors start at 6,000 lineal feet.
Should I choose Soleo 6008 or Soleo 6010?
Soleo 6008 measures 2 × 1¼ in. and weighs 0.57 lb/ft, so it suits fine, closely spaced slats. Soleo 6010 measures 5⅛ × 2⅛ in. and weighs 1.55 lb/ft, so it suits deeper blades and longer spans between supports. They are our two most-specified profiles, share the same core, skin, colors and warranty, and can be combined on one project, as at Governor’s Plaza in Maryland.
Which other profiles can be used for louvers?
All of them. Our Architectural Elements range has 33 profiles: 18 Soleo battens, 7 Planeo fins and planks, 6 Careo square posts and 2 Diameo diamond fins, and every one can be used for louvers, privacy screens, sunshades, decorative screens and brise-soleil. Every profile is a hot co-extrusion of aluminum and wood composite that meets the IBC 2018 703.5.2 definition of composite noncombustible, offered in Teak, Rosewood, Ebony and Moleskin. Soleo 6008 and 6010 are shown in detail on this page as examples. Contact our team to confirm the right profile and quantity for your project.
How long does a louvered screen last, and what is covered?
Soleo is tested for weathering to 5,000 hours under JIS A 1415 and carries a 10-year non-prorated limited warranty. Read the warranty document for the full terms.
Ready to see it in hand?
Order a physical sample box, or request a quote sized to your screen.

