Decorative Screens
Decorative screen panels for outdoors, built from Geolam aluminum-core profiles with a sanded wood-look face. Designed by architects as facade screens, feature walls and screen walls on commercial buildings, with no staining or sealing.
A screen wall where the pattern is the point.
A decorative screen is a row of slats, fins or planks fixed to a frame, where the main job is how it looks: the rhythm of the slats, the shadows they cast and the way light passes through. On commercial buildings a decorative screen wall shows up as facade screens, entrance feature walls, parking garage skins, courtyard walls and screens around rooftop equipment.
Geolam supplies the profiles, not ready-made panels. Each decorative screen panel is drawn by the architect and built on site from Soleo, Planeo, Careo or Diameo profiles fastened to a subframe. That means the panel size, slat spacing and pattern are set per project, and every slat has an aluminum core under a sanded wood-composite skin.
If the screen’s main job is to block views, a decorative privacy screen is covered on Privacy Screens. If it is shading glass, see Sunshade Systems.
Pattern by design
Profile mix, spacing and direction set the look.
Aluminum core
Anodized A6063S-T5 alloy inside every slat.
Non-combustible
Soleo 6008 and 6010 tested to ASTM E136 (datasheet appendix).
Wide range
33 profiles: battens, fins, planks, square posts.
From extrusion to a finished decorative screen.
Every slat is made in one hot co-extrusion: an anodized aluminum core and a wood-composite skin. On site, the slats are cut, capped and fastened to a subframe to make each screen panel.
1. The slat: each Soleo profile is an anodized aluminum core (A6063S-T5) bonded to a wood-composite skin in one co-extrusion, then sanded. The core keeps long slats straight; the skin gives them grain and color.
2. Subframe and posts: steel or aluminum rails, or Careo square posts, hold the slats. Their size and spacing are set by the project engineer for wind load and the supporting structure.
3. Cutting: slats are cut with powered aluminum-cutting chip saws (carbide tips), never grinders or chainsaws. Planeo boards can only be shortened at the 2 in. ends beyond their internal bolts.
4. Fastening: Geolam’s installation guide uses InPull nuts (M6 to M12), blind nuts or bolts, with pre-drilled holes 2 to 4 mm larger than the bolt and washers, so each slat can move with temperature. Tapping screws, drill screws and nails are not recommended.
5. Finishing: end caps close the open ends of each slat. They are glued, and their four weep openings must stay open so water can drain. Soleo 6008 and 6010 also take splice connectors for long runs.
Six ways to build a decorative screen pattern.
Most decorative screen designs come from four choices: which profiles, how far apart, which direction and which colors. Soleo 6008 and 6010 are our two most-specified profiles, and every profile in the range can be used for decorative screens.
| Screen type | What it looks like | Where it’s used | Geolam option |
|---|---|---|---|
| Batten screen wallGeolam Soleo 6008 | Slim slats at an even spacing; reads as fine texture from a distance | Entrances, facade feature walls, courtyards | Soleo 6008, 2 × 1¼ in. |
| Deep-fin screenGeolam Soleo 6010 | Deeper fins cast strong shadow lines that change through the day | Facades, parking structures, stair towers | Soleo 6010, 5⅛ × 2⅛ in. |
| Mixed-width rhythm | Two or more sections alternated in a repeating sequence | Facade bays, entrance canopies | Any Soleo mix, e.g. 6008 + 6010 at Governor’s Plaza |
| Diamond-fin screen | Faceted fins catch light differently on each face | Feature walls, building corners | Diameo 2018 or 2023 |
| Wide-plank screen | Broad planks with narrow gaps for a bold, large-scale pattern | Parking garages, equipment screens | Planeo 4123 to 4062 |
| Post-and-slat screen | Square posts with slats set between them | Terraces, courtyards, decorative screen dividers | Careo posts with Soleo slats |
Outdoor decorative screen panels that read as wood.
An outdoor decorative screen is seen up close, every day, by everyone who walks past. Geolam’s Soleo 6008 and Soleo 6010, our two most-specified profiles, give it a sanded wood grain with an aluminum core doing the structural work.
Get Your SamplesThe profiles: Soleo 6008 and Soleo 6010
Our two most-specified profiles, shown as examples; every profile in the range below can be used for decorative screens. Both are stocked in Teak and Rosewood with no minimum order.
Soleo 6008 · 2 × 1¼ in.

Our most-specified profile. A slim batten for closely spaced slats and a fine, even pattern. It is used with Soleo 6010 on Governor’s Plaza, shown on this page.
| Section | 2 × 1¼ in. | 50 × 30 mm |
| Weight | 0.57 lb/ft | 0.85 kg/m |
| Standard length | 9 ft 10 in. | 3.0 m |
| Custom lengths | 7 ft to 19 ft 8 in. | 2.15 to 6 m |
| Est. span between supports† | About 8 ft at 100 mph wind |
| End caps / splices | Yes / Yes |
| Fire rating | Non-combustible, ASTM E136 (appendix) |
| Core | Anodized aluminum alloy A6063S-T5 |
| Warranty | 10-year limited, non-prorated |
*1,000 lineal ft minimum. **Non-standard color, 90-day lead time, 5,000 lineal ft minimum. †Estimated from Geolam’s wind-load span chart; confirm with a design professional.
Soleo 6010 · 5⅛ × 2⅛ in.

A deep, multi-chamber fin. Its 2⅛ in. depth casts strong shadow lines and spans farther between supports than Soleo 6008. It is the profile on the Grammy Museum and Completely Kids screens shown on this page.
| Section | 5⅛ × 2⅛ in. | 128 × 53 mm |
| Weight | 1.55 lb/ft | 2.30 kg/m |
| Standard length | 9 ft 10 in. | 3.0 m |
| Custom lengths | 7 ft to 19 ft 8 in. | 2.15 to 6 m |
| Est. span between supports† | About 13 ft at 100 mph wind |
| End caps / splices | Yes / Yes |
| Fire rating | Non-combustible, ASTM E136 (appendix) |
| Core | Anodized aluminum alloy A6063S-T5 |
| Warranty | 10-year limited, non-prorated |
*1,000 lineal ft minimum. **Non-standard color, 90-day lead time, 5,000 lineal ft minimum. †Estimated from Geolam’s wind-load span chart; confirm with a design professional.
33 profiles in four families.
Every Architectural Elements profile can be used for decorative screens, as well as louvers, privacy screens, sunshades and brise-soleil. Mixing sections from different families is one of the easiest ways to make a screen pattern your own. Soleo 6008 and 6010 are shown in detail above as examples; the tiles below cover every Soleo batten, Planeo fin and plank, Careo square post and Diameo diamond fin. Check the datasheet for the fire rating of the profile you specify.
Soleo
1¾ × 1 in. Soleo 6027Slimmest
1⅝ × 1¼ in. Soleo 6008Batten
2 × 1¼ in. Soleo 6029Medium-Width
2⅜ × 1¼ in. Soleo 6026Square-Profile
2⅜ × 1⅝ in. Soleo 6011Broad-Profile
2¾ × 1⅝ in. Soleo 6030Plank-Style
3⅛ × 1¼ in. Soleo 6017Multi-Chamber
3⅝ × 1⅝ in. Soleo 6036Ultra-Flat Slat
4 × ⅝ in. Soleo 6009Wide
4 × 1¼ in. Soleo 6034Deep
4⅛ × 2⅛ in. Soleo 6031Wide-Slim
5 × 1⅛ in. Soleo 6010Deep
5⅛ × 2⅛ in. Soleo 6038Wide-Flat
5¾ × ⅞ in. Soleo 6024Wide
5¾ × 1¼ in. Soleo 6040Wide-Deep
6 × 2 in. Soleo 6050Large
6 × 4 in. Soleo 6033Wide-Format
7⅞ × 1⅜ in.
Planeo
5¾ × 1¼ in. Planeo 4044Fin (Deep)
6⅞ × 3⅜ in. Planeo 4123Plank (Slim Wide)
11⅜ × 1¼ in. Planeo 4048Plank (Broad Wide)
11¾ × 2 in. Planeo 4061Plank (Deep)
11¾ × 4 in. Planeo 4046Fin (Wide Large-Scale)
13¾ × 4¼ in. Planeo 4062Plank (Extra-Wide)
17¾ × 4 in.
Careo
1¾ × 1¾ in. Careo 7031Square Post
1¾ × 1¾ in. Careo 7011Square Post
2⅛ × 2⅛ in. Careo 7035Square Post
3⅜ × 3⅜ in. Careo 7014Square Post
3½ × 3½ in. Careo 7016Square Post
4¾ × 4¾ in.
Diameo
Tiles show each cross-section to the same scale (width × depth), in inches.
Standard length is 9 ft 10 in for Soleo, Planeo 4010, Careo and Diameo 2018, with custom lengths up to 19 ft 8 in (Soleo 6026 up to 18 ft). The other Planeo profiles and Diameo 2023 are made to custom length, up to 26 ft. Planeo boards are built from hybrid profiles bolted together internally, so they can be shortened only at the 2 in. ends beyond the end bolts. Qualita decking is a separate product line and is not listed here.
Soleo Slats vs. Other Decorative Screen Materials
How an aluminum-core hybrid slat compares with the five materials most often used for outdoor decorative screens.
| Parameter | Geolam Soleo (Aluminum-Core Hybrid) | Solid Wood Slats | Aluminum Slats or Panels | Solid WPC Slats | Terracotta Baguettes | Rice Hull / PVC Composite |
|---|---|---|---|---|---|---|
| Construction | ✓ Anodized aluminum core with a co-extruded wood-composite skin. | Solid timber throughout. | Aluminum throughout, with a coated or anodized surface. | Wood fiber and plastic, no metal core. | Fired clay sections. | Rice hulls bound in PVC. |
| Fire Classification | ✓ Soleo 6008 and 6010 non-combustible, ASTM E136; Class A, ASTM E84. | ✗ Combustible unless treated. | ✓ Non-combustible. | ✗ Class A, but not non-combustible. | ✓ Non-combustible. | ✗ Class A, but not non-combustible. |
| Appearance | ✓ Sanded natural grain with color variation. | ✓ Genuine grain, varies by species and cut. | ✗ Metallic; a wood look needs a printed or sublimated coating. | Brushed composite surface. | Clay finish, glazed or natural; no wood grain. | Needs a finish coat for color. |
| Maintenance | ✓ Soap and water or power washing; no staining or sealing cycle. | ✗ Periodic staining or sealing to hold its color. | Depends on the coating. | Follow the manufacturer’s care guide. | ✓ Low. | ✗ Finish needs periodic re-coating. |
| Weight & Length | ✓ 0.57 lb/ft (Soleo 6008) to 1.55 lb/ft (Soleo 6010); custom lengths up to 19 ft 8 in. | ✗ Limited by available timber lengths. | Typically 12–24 ft stock lengths. | 12 ft standard lengths. | ✗ Around 8 lb/ft; pieces up to about 6 ft. | 12 ft standard lengths. |
| Warranty | ✓ 10-year, non-prorated. | Varies by supplier and species. | Varies by supplier and coating. | Often around 5 years. | ✓ Often 30 years. | Material warranty; finish often not covered. |
General category patterns from Geolam’s material comparison charts; individual products vary by manufacturer.
Download the Full Materials Comparison GuideWhat makes this the right decorative screen material.
A decorative screen panel repeats the same slat hundreds of times, so small flaws show. The aluminum core keeps long slats straight between supports, and it will not rot, split or attract termites the way solid timber can. The sanded skin gives each slat real grain instead of a pattern printed onto metal.
The wood fiber is dried to 0% moisture content before extrusion, which helps the skin resist warping and mold. The skin uses polypropylene rather than PVC, the material contains 70–80% recycled content, and it is 100% recyclable at end of life, with the Japan Environmental Association’s Eco-Mark.
A decorative screen is judged up close.
Decorative outdoor screen panels usually sit at street level, at entrances and around courtyards, where people walk past them every day. Uneven color, a sagging slat or a chipped coating is easy to spot, and fixing it on a finished building means scaffolding and downtime.
A hybrid slat avoids the usual trade-off: timber looks right but needs refinishing, and plain aluminum lasts but looks like metal. Soleo profiles give the look of a decorative wood screen with an aluminum core, and they are also used as decorative screen dividers on terraces, rooftop decks and outdoor dining areas.
Keeping a slat screen clean.
Open slats catch dust, pollen and leaves in the gaps. Rain clears most of it; the rest comes off with water and mild soap, and power washing is fine: it does not affect the warranty. There is no staining, sealing or repainting cycle, because the sanded surface is the finish itself.
Geolam’s 10-year non-prorated warranty covers the profile against splitting, splintering, rot and termite or fungal decay. Like most exterior finishes, normal weathering and color change over time are excluded, so look at a physical sample before you choose a color.
Long slats move with the temperature.
An exterior decorative screen faces full sun, rain and coastal air. Soleo’s finish is weathering-tested under DIN ISO 16474-2 and to 5,000 hours under JIS A 1415, and salt-spray tested under DIN EN ISO 9227, which matters on coastal projects like the Naples parking garage in Florida.
Like any aluminum, the core grows and shrinks slightly with temperature: about 0.92 mm per meter over a 40 °C (72 °F) swing. Oversized pre-drilled holes and washers at each fastener let each slat move freely. Screens also catch wind, so use Geolam’s wind-load span charts for early sizing and have the engineer of record confirm the support spacing.
Who stands behind these profiles?
Geolam, Inc. is headquartered in Toronto, Ontario, and is the exclusive North American importer and distributor of Geolam® exterior building products manufactured in Japan. The hybrid wood-aluminum technology was developed in Japan in the 1990s, and Geolam introduced its Wood Hybrid Systems (WHS) triple-extrusion profiles in 2012.
Geolam supplies the profiles; the screen itself is designed by the project team. Architects, specifiers, developers, contractors and installers order through Geolam or your local Geolam sales representative. Soleo 6008, 6010, 6031 and 6033 are stocked in Teak and Rosewood with no minimum order.
Certifications & performance attributes
Fire data applies to Soleo 6008 and 6010; check each datasheet for other profiles.
Your pattern
Profile mix, spacing and direction are drawn per project, not chosen from a catalog panel.
Light and air through
Open slats filter views and sun without closing a space in.
Code-friendly
Soleo 6008 and 6010 are ASTM E136 non-combustible, and Class A under ASTM E84.
Long custom lengths
Slats from 7 ft up to 19 ft 8 in., with splice connectors for longer runs.
Geolam decorative screens on built projects
Five decorative screens from our project gallery.
Governor’s Plaza — MarylandSoleo 6008 and 6010, Teak — decorative screen
Grammy Museum — MississippiSoleo 6010, Rosewood — decorative screen
Completely Kids — NebraskaSoleo 6010, Teak — decorative screen
Rosecrans Ave — CaliforniaSoleo 6030 and 6031, Teak — decorative screen
Centene Office Building — MissouriSoleo 6033, Teak — decorative screen
Governor’s Plaza mixes the two featured profiles; Grammy Museum and Completely Kids use Soleo 6010, Rosecrans uses Soleo 6030 and 6031, and Centene uses the wide Soleo 6033. Ask your local Geolam sales representative for commercial decorative screen references close to your building type.
See All Projects in the GalleryStandard finishes & sections
Soleo 6008 and 6010 in six wood-look tones.

Teak
Warm, golden hardwood tone
Rosewood
Deep reddish hardwood tone
Moleskin*
Cool, driftwood grey
Ebony*
Near-black, low-sheen finish
Carbon**
Deep matte black
Bilinga**
Rich amber-brown hardwood toneFor Soleo 6008, 6010, 6031 and 6033: *1,000 lineal ft minimum. Every other profile has a 1,000 lineal ft minimum in any standard color. **Non-standard color, 90-day lead time, 5,000 lineal ft minimum.
Color is a pattern tool on a decorative screen: alternating Teak and Rosewood slats, or using a dark tone behind a light one, changes the screen without changing the profiles. Soleo 6008, 6010, 6031 and 6033 are stocked in the USA in Teak and Rosewood with no minimum order, and Moleskin and Ebony carry a 1,000 lineal ft minimum. Every other profile in the range has a 1,000 lineal ft minimum in any standard color.
Carbon and Bilinga are non-standard colors with a 90-day lead time and a 5,000 lineal ft minimum, and fully custom colors start at 6,000 lineal ft. Because the face is sanded, grain and shading vary naturally between production runs, so compare a physical sample in daylight before you commit.
Request Physical Samples
The two featured sections, side by side
Soleo 6008 and Soleo 6010 drawn to the same scale, so the difference in width and depth is easy to judge.
The dark band in each outline marks the aluminum core and the colored band the composite skin. The slim 6008 gives a fine, even texture; the deeper 6010 gives bolder shadow lines. The drawings show proportion only; use the datasheets for actual profile geometry.
What affects decorative screen cost?
Pricing varies too much by project to quote one number. These are the factors that move it.
Get a project-specific number
Send elevations, screen heights, slat spacing, preferred profiles and colors, and the project location to Geolam or your local Geolam sales representative.
Request a Quote Find Your Local RepWhat architects say
Architects on specifying Geolam Architectural Elements.
“It’s particularly good for spaced out slat applications, where the homogenous nature of the material is a desired quality.”
“We chose Geolam for its warm wood aesthetics, color retention and low maintenance.”
“Geolam provided a great solution for the courtyard trellis. A superior product which accents the main entrance to the community center.”
Decorative screens, common questions
What is a decorative screen?
A decorative screen is a row of slats, fins or planks fixed to a frame, where the main job is appearance: the rhythm of the slats, the shadows they cast and the light that passes through. On commercial buildings it is used for facade screens, entrance feature walls, parking garage skins, courtyard walls and equipment screens. Geolam supplies the profiles; the screen is designed by the project team.
Does Geolam sell ready-made decorative screen panels?
No. Geolam supplies the profiles: Soleo battens, Planeo fins and planks, Careo square posts and Diameo diamond fins. The architect sets each decorative screen panel’s size, spacing and pattern, and the contractor or installer fastens the profiles to a subframe on site. Orders go through Geolam or your local Geolam sales representative.
Which material is best for a decorative screen panel outdoor?
Outdoors, the screen has to handle sun, rain, wind and fire codes as well as look good. Solid wood needs refinishing and is combustible; plain aluminum lasts but looks like metal. Geolam Soleo profiles combine an aluminum core with a sanded wood-composite skin, and Soleo 6008 and 6010 are non-combustible under ASTM E136.
How do you create a pattern with outdoor decorative screen panels?
Four choices set the pattern: which profiles (mixing widths, such as Soleo 6008 with 6010), how far apart they are, whether they run vertically, horizontally or at an angle, and which colors are used. Diameo diamond fins add faceted light and shadow. The design team draws the pattern per elevation, and physical samples help confirm it before ordering.
Can Careo profiles be used for a corner post decorative screen?
Yes. Careo profiles are square aluminum-core posts from 1¾ in. to 4¾ in., so they can form the corner post of a decorative screen, with Soleo slats set between them. Post sizing and anchorage are designed by the project engineer for the screen height and wind load.
Is a Geolam screen the same as an aluminum batten screen?
It is an aluminum batten screen with a difference. Unlike a plain decorative aluminum screen, each Soleo batten has an anodized aluminum alloy core (A6063S-T5) co-extruded with a sanded wood-composite skin, so it is as straight and durable as aluminum but looks like timber, without a painted or printed wood pattern.
Can decorative screen dividers be used on terraces and courtyards?
Yes. Decorative screen dividers built from Geolam profiles are used to separate outdoor dining areas, rooftop decks, terraces and courtyards on hotels, offices and multifamily buildings. They are fixed to a structure designed by the project team rather than freestanding.
Is this a folding decorative screen?
No. A folding decorative screen is a freestanding furniture piece with hinges. Geolam profiles are for fixed architectural screens that are fastened to a building or a structural frame.
Are Geolam decorative screens non-combustible?
Soleo 6008 and 6010 are listed as non-combustible as per ASTM E136 (appendix) on their datasheets, and Geolam profiles are rated Class A under ASTM E84; ASTM E136 is the stricter test. Fire data can vary by profile, so confirm the specific profile and source document with your code consultant.
Can a decorative screen hide rooftop equipment?
Yes. Mechanical and air conditioner screens are a common use, on rooftops, at service yards and around ground-level units. Leave enough open area between slats for the airflow the equipment needs, and have the subframe designed for wind load.
How are decorative screen panels installed?
The profiles are fastened to a steel or aluminum subframe with InPull nuts, blind nuts or bolts, through pre-drilled holes 2 to 4 mm oversize with washers so each slat can move with temperature. End caps are glued on with their weep openings left clear. Follow Geolam’s Architectural Elements installation guide.
What colors are available, and are there minimums?
Standard colors are Teak, Rosewood, Moleskin and Ebony. Soleo 6008, 6010, 6031 and 6033 are stocked in the USA with no minimum in Teak and Rosewood, and a 1,000 lineal ft minimum in Moleskin and Ebony. Every other profile has a 1,000 lineal ft minimum in any standard color. Carbon and Bilinga start at 5,000 lineal ft, and custom colors at 6,000 lineal ft.
What lengths do the profiles come in?
Soleo, Planeo 4010, Careo and Diameo 2018 have a standard length of 9 ft 10 in (3.0 m), with custom lengths from 7 ft to 19 ft 8 in on most profiles. The other Planeo boards and Diameo 2023 are made to custom length, up to 26 ft.
How do you maintain an outdoor decorative screen?
Rain keeps most slats clean. For dust or dirt in the gaps, wash with water and mild soap; power washing is fine and does not affect the warranty. Soleo profiles never need staining, sealing or refinishing.
What does the warranty cover?
Geolam provides a 10-year non-prorated limited warranty: the profiles will not split, splinter, rot or suffer termite or fungal decay damage. It excludes color variation, normal weathering, improper installation and non-Geolam fasteners.
How do I get pricing or samples for a decorative screen project?
Send elevations, screen heights, slat spacing, preferred profiles and colors, and the project location to Geolam or your local Geolam sales representative. Order a physical sample before finalizing colors, since a screen will not show the sanded surface accurately.
Ready to see it in hand?
Order a physical sample box, or get a project quote from your local Geolam representative.

