Privacy Screens
Wood-look privacy screens built from Geolam Soleo and Planeo profiles: an anodized aluminum core co-extruded with a sanded wood-composite skin. The warmth of timber for decks, balconies, rooftops and facades, without the refinishing.
A screen wall that blocks the view, not the air.
Privacy screens are rows of battens, slats or boards spaced to block sightlines while letting light and air through. On commercial and multifamily projects they divide balconies, screen rooftop equipment, enclose amenity decks and courtyards, and add a layered wood-look plane to a facade.
Geolam does not sell finished screen kits. Geolam manufactures the profiles that architects specify and installers mount on a subframe, which is why exterior privacy screens built with Soleo and Planeo suit custom geometry, long runs and code-driven commercial work.
Aluminum core
Anodized A6063S-T5 extrusion carries the span.
Sanded composite skin
Real wood-grain texture, not a printed film.
Non-combustible
ASTM E136 per the datasheets of the featured profiles.
Vertical or horizontal
Battens, slats or wide boards, either orientation.
From extrusion to a finished privacy screen.
Each profile is co-extruded in one pass, then cut, capped and fastened to a subframe on site. The steps below follow the Geolam Architectural Elements installation guide.
1. Aluminum core: an anodized aluminum alloy extrusion (A6063S-T5) gives each batten its stiffness and straightness.
2. Bonding layer: an olefin-resin layer bonds the core to the skin so the two move as one.
3. Composite skin: regenerated wood flour and polypropylene with a non-halogenated flame retardant, sanded to a natural grain.
4. Cutting: aluminum-cutting carbide saws only; no grinders or chainsaws. End caps are glued on and their weep openings stay clear.
5. Fastening: through-bolts, InPull nuts or blind nuts into a steel or aluminum subframe. Holes are pre-drilled 2–4 mm oversize with washers to allow thermal movement. Tapping screws, drill screws and nails are not recommended.
6. Spacing: the gap between profiles sets the level of privacy, and is drawn per elevation by the design team.
One profile family, many kinds of privacy screen.
Privacy comes from the ratio of profile width to gap. Wider faces with tighter spacing block more view; deeper profiles span farther between supports.
| Screen type | Typical profile | Privacy level | Where it’s used |
|---|---|---|---|
| Vertical batten screenGeolam Soleo 6008 | Soleo 6008, 2 × 1¼ in | Partial to high, set by spacing | Balconies, rooftop decks, residential terraces |
| Horizontal slat screen | Soleo 6031 (5 in) or Soleo 6033 (7⅞ in) | High, narrow gaps | Courtyards, amenity decks, property lines |
| Angled fin screen | Soleo 6033 or 6010 on rotated brackets | Blocks direct sightlines, keeps airflow | Office terraces, parking structures |
| Tall facade screen | Soleo 6010 (5⅛ × 2⅛ in) | Partial, layered depth | Multi-story facades, stair towers |
| Solid-look screen wall | Planeo 4123 (11⅜ × 1¼ in) | Near-solid | Equipment screens, service yards |
Outdoor privacy screens that read as wood, up close.
Geolam’s Soleo 6008 and Soleo 6010 are our two most-specified profiles, and every profile in the range can be spaced into a privacy screen.
Get Your SamplesThe profiles: Soleo 6008 and Soleo 6010
Our two most-specified profiles, shown as examples: a slim batten for open vertical screens and a deep blade for taller, windier screens. Every profile in the range below can be used. Both are stocked in Teak and Rosewood with no minimum order.

Soleo 6008 · 2 × 1¼ in
| Width × depth | 2″ × 1¼” | 50 × 30mm |
| Weight | 0.57 lb/ft | 0.85 kg/m |
| Standard length | 9’10” | 3.0m |
| Custom lengths | 7 ft – 19’8″ | 2.15m – 6m |
| Minimum order | Teak, Rosewood: none. Moleskin, Ebony: 1,000 lin ft |
| Fire rating | Non-combustible, ASTM E136 (appendix) |
| Accessories | End caps, splice connector |

Soleo 6010 · 5⅛ × 2⅛ in
| Width × depth | 5⅛” × 2⅛” | 128 × 53mm |
| Weight | 1.55 lb/ft | 2.30 kg/m |
| Standard length | 9’10” | 3.0m |
| Custom lengths | 7 ft – 19’8″ | 2.15m – 6m |
| Minimum order | Teak, Rosewood: none. Moleskin, Ebony: 1,000 lin ft |
| Fire rating | Non-combustible, ASTM E136 (appendix) |
| Core | Anodized aluminum alloy A6063S-T5 |
*Non-standard color, 90-day lead time, 5,000 lineal ft minimum.
33 profiles in four families.
Any of these profiles can be spaced into a privacy screen. Each is a hot co-extrusion of anodized aluminum and wood composite. Soleo 6008 and 6010 are shown in detail above as examples; the tiles below cover every Soleo batten, Planeo fin and plank, Careo square post and Diameo diamond fin in the Architectural Elements range. Check the datasheet for the fire rating of the profile you specify.
Soleo
1¾ × 1 in. Soleo 6027Slimmest
1⅝ × 1¼ in. Soleo 6008Batten
2 × 1¼ in. Soleo 6029Medium-Width
2⅜ × 1¼ in. Soleo 6026Square-Profile
2⅜ × 1⅝ in. Soleo 6011Broad-Profile
2¾ × 1⅝ in. Soleo 6030Plank-Style
3⅛ × 1¼ in. Soleo 6017Multi-Chamber
3⅝ × 1⅝ in. Soleo 6036Ultra-Flat Slat
4 × ⅝ in. Soleo 6009Wide
4 × 1¼ in. Soleo 6034Deep
4⅛ × 2⅛ in. Soleo 6031Wide-Slim
5 × 1⅛ in. Soleo 6010Deep
5⅛ × 2⅛ in. Soleo 6038Wide-Flat
5¾ × ⅞ in. Soleo 6024Wide
5¾ × 1¼ in. Soleo 6040Wide-Deep
6 × 2 in. Soleo 6050Large
6 × 4 in. Soleo 6033Wide-Format
7⅞ × 1⅜ in.
Planeo
5¾ × 1¼ in. Planeo 4044Fin (Deep)
6⅞ × 3⅜ in. Planeo 4123Plank (Slim Wide)
11⅜ × 1¼ in. Planeo 4048Plank (Broad Wide)
11¾ × 2 in. Planeo 4061Plank (Deep)
11¾ × 4 in. Planeo 4046Fin (Wide Large-Scale)
13¾ × 4¼ in. Planeo 4062Plank (Extra-Wide)
17¾ × 4 in.
Careo
1¾ × 1¾ in. Careo 7031Square Post
1¾ × 1¾ in. Careo 7011Square Post
2⅛ × 2⅛ in. Careo 7035Square Post
3⅜ × 3⅜ in. Careo 7014Square Post
3½ × 3½ in. Careo 7016Square Post
4¾ × 4¾ in.
Diameo
Profiles drawn to the same scale, simplified outlines for proportion only. Section sizes in inches.
Standard length is 9 ft 10 in for Soleo, Planeo 4010, Careo and Diameo 2018, with custom lengths up to 19 ft 8 in (Soleo 6026 up to 18 ft). The other Planeo profiles and Diameo 2023 are made to custom length, up to 26 ft. Planeo boards are built from hybrid profiles bolted together internally, so they can be shortened only at the 2 in. ends beyond the end bolts. Qualita decking is a separate product line and is not listed here.
See the Full Architectural Elements RangeSoleo Profiles vs. Other Privacy Screen Materials
A best durable outdoor privacy screens materials comparison: how Geolam hybrid profiles stack up against the five materials they are most often specified against.
| Parameter | Geolam Soleo (Aluminum-Core Hybrid) | Natural Wood (Ipe, Cedar) | Wood-Look Printed Aluminum | Solid WPC Boards | Terracotta Baguettes | Rice Hull / PVC Composite |
|---|---|---|---|---|---|---|
| Surface Appearance | ✓ Sanded wood-composite face, natural grain variation. | ✓ Real wood, weathers to grey. | ✗ Printed or sublimated pattern over metal. | Brushed composite surface. | Clay finish, glazed or natural; no wood grain. | Needs a finish coat for color. |
| Refinishing | ✓ None required. | ✗ Regular refinishing. | ✓ None, but finish scratches show. | ✓ None required. | ✓ None required. | ✗ Finish needs periodic re-coating. |
| Ongoing Maintenance | ✓ Soap and water, or power washing. | ✗ Sealing and cleaning schedule. | ✗ Annual cleaning log for some finish warranties. | Follow the manufacturer’s care guide. | ✓ Low. | Follow the manufacturer’s care guide. |
| Custom Lengths | ✓ Up to 19’8″ (6m). | ✗ Typically 8–12 ft. | ✗ Typically 12, 16 or 24 ft. | ✗ 12 ft standard. | ✗ Pieces up to about 6 ft; around 8 lb/ft. | ✗ 12 ft standard. |
| Warranty | ✓ 10-year non-prorated. | ✗ None. | ✗ Finish coverage often about 1 year. | Often around 5 years. | ✓ Often 30 years. | Material warranty; finish often not covered. |
| Fire Rating | ✓ ASTM E136 non-combustible (featured profiles); Class A, ASTM E84. | ✗ Combustible; fire retardant needed for most commercial codes. | ✓ ASTM E136 non-combustible. | ✗ Class A, but not non-combustible. | ✓ Non-combustible. | ✗ Class A, but not non-combustible. |
Based on Geolam’s comparison charts; individual competitor products vary by brand. Geolam’s warranty excludes color variation and normal weathering.
Download the Full Materials Comparison GuideWhat makes this the right privacy screen material.
The aluminum core gives each batten span and straightness, so long privacy screen runs stay true. The sanded composite skin gives the warmth clients want from timber, and the 10-year warranty covers splitting, splintering, rot, and termite or fungal decay damage.
Profiles can be curved to a 16 in minimum radius for rounded screens, and custom lengths up to 19’8″ reduce joints on long walls. The wood fiber is dried to 0% moisture before extrusion, and the skin uses polypropylene rather than PVC.
Privacy screens sit where people live, work and gather.
Balcony dividers, rooftop amenity screens and courtyard walls are seen and touched up close every day. A material that splinters, checks or needs scaffolding to refinish turns into an operating cost.
On taller buildings, combustible screens on balconies and decks draw code scrutiny. Specifying a profile whose datasheet lists ASTM E136 non-combustible gives the design team a documented starting point; confirm the specific profile and source document with your code consultant. The same profiles also work for office privacy screens on corporate terraces and campus courtyards, so indoor-outdoor zones share one wood-look finish.
Keeping a slat screen clean.
Rain usually keeps the profiles clean. For stubborn dirt, wash with warm water and mild dish soap, working bottom to top, then rinse top to bottom. There is no staining, sealing or painting schedule.
Power washing is fine and does not affect the warranty. Keep end-cap weep openings clear and check fasteners and washers during routine building inspections.
Built for sun, wind and freeze-thaw.
The profiles are weathering-tested to 5,000 hours (JIS A 1415). Like any exterior material, they will show some natural weathering over time, which the warranty treats as normal.
Long battens move with temperature: about 0.92 mm per meter over a 40°C swing, which the oversized holes and washers absorb. Privacy screens also catch wind, so use the Geolam wind-load span charts for early sizing and have the engineer of record confirm final spans.
Who makes Geolam privacy screen profiles?
Geolam, Inc. is headquartered in Toronto, Ontario, and is the exclusive North American importer and distributor of Geolam® premium exterior building products manufactured in Japan. The hybrid wood-aluminum technology was developed in Japan in the 1990s, and in 2012 Geolam introduced Wood Hybrid Systems: triple-extrusion profiles combining an aluminum core with a wood-composite skin.
Geolam supplies the profiles; the screen itself is designed by the project team. Architects, specifiers, developers, contractors and installers order through Geolam or your local Geolam sales representative.
Certifications & performance attributes
Privacy you can tune
Profile width and spacing set the level of screening, elevation by elevation.
Air and light pass through
Open slats screen views without trapping heat or blocking breezes.
Code-friendly
ASTM E136 non-combustible on the featured profiles’ datasheets.
No refinishing
Weather-resistant sanded finish with no stain or sealer cycle.
Geolam privacy screens on built projects
Three privacy screens and two decorative screens, from our project gallery.
Gun Lake Casino Resort — MichiganSoleo 6034, Teak — privacy screen
Biloxi Pedestrian Bridge — MississippiSoleo 6034, Moleskin — privacy screen
Cici & Hyatt Brown Art Museum — FloridaCareo 7014, Moleskin — privacy screen
Completely Kids — NebraskaSoleo 6010, Teak — decorative screen
City of Naples Parking Garage — FloridaSoleo 6033, Rosewood — decorative screen
These projects use Soleo and Careo profiles across Michigan, Mississippi, Florida and Nebraska. More installations, including screens, sunshades and canopies, are in the Geolam project gallery.
See All Projects in the GalleryStandard finishes & sections
The same sanded finish across the Soleo range.

Teak
Warm, golden hardwood tone
Rosewood
Deep reddish hardwood tone
Moleskin*
Cool, driftwood grey
Ebony*
Near-black, low-sheen finish
Carbon**
Deep matte black
Bilinga**
Rich amber-brown hardwood tone*Standard color, 1,000 lineal ft minimum on Soleo 6008, 6010, 6031 and 6033 (Teak and Rosewood have no minimum). Every other profile has a 1,000 lineal ft minimum in any standard color. **Non-standard color, 90-day lead time, 5,000 lineal ft minimum.
Because the finish is sanded rather than printed, expect natural variation in grain and shading between production runs, the same way hardwood varies board to board. Order each privacy screen in a single run where possible.
Fully custom colors are available above a 6,000 lineal foot minimum. For color-critical projects, request a current physical sample rather than relying on a screen.
Request Physical Samples
The two featured sections, side by side
Soleo 6008 and Soleo 6010 drawn to the same scale, so the difference in width and depth is easy to judge.
The dark band in each outline marks the aluminum core and the colored band the composite skin. The drawings show proportion only; use the datasheets for the actual profile geometry.
What affects privacy screen cost?
Pricing varies too much by project to quote a single number honestly. Here’s what actually drives it.
Get a project-specific number
Send elevations with screen heights, run lengths, profile, spacing and finish to Geolam or your local Geolam sales representative.
Request a Quote Find Your Local RepWhat architects say
Architects on specifying Geolam Architectural Elements.
“Architectural Elements were chosen for their low maintenance composite wood finish, and clean aesthetic with warm wood tones that married perfectly with our material palette.”
“It’s particularly good for spaced out slat applications, where the homogenous nature of the material is a desired quality.”
“Geolam’s Soleo 6031 delivers the warm wood aesthetics we were looking for and its low maintenance is an added bonus.”
Privacy screens, common questions
What are privacy screens made of at Geolam?
Geolam privacy screens are built from hybrid profiles: an anodized 6063-T5 aluminum core, an olefin-resin bonding layer and a sanded wood-composite skin. The result looks like timber but carries loads like aluminum.
Does Geolam sell finished privacy screen kits?
No. Geolam manufactures the profiles (battens, slats, fins and boards). Your architect specifies the layout and your contractor or installer mounts the profiles on a subframe. Orders go through Geolam or your local Geolam sales representative.
Which profile is best for outdoor privacy screens?
Soleo 6008 (2 x 1 1/4 in, 0.57 lb/ft) and Soleo 6010 (5 1/8 x 2 1/8 in, 1.55 lb/ft) are our two most-specified profiles. Soleo 6008 suits balcony and deck screens; the deeper Soleo 6010 spans farther in tall or windy locations. For more coverage per board, Soleo 6031 (5 in wide) or Soleo 6033 (7 7/8 in wide) work well, and every profile in the range can be used.
Can Geolam profiles be used as privacy screens for decking?
Yes. Privacy screens for decking, rooftop decks and amenity terraces are a common use. Slim Soleo battens such as Soleo 6008 fit post-and-rail framing, and the profiles will not rot, split or splinter under the 10-year warranty.
Are exterior privacy screens from Geolam non-combustible?
The featured profiles, Soleo 6008 and 6010, are listed as non-combustible under ASTM E136 on their datasheets, and Geolam profiles are rated Class A under ASTM E84; ASTM E136 is the stricter test. Fire data can vary by profile, so confirm the specific profile and source document with your code consultant.
How much privacy does a slat screen give?
Privacy depends on the gap between profiles relative to their width, and on the viewing angle. Wide boards with narrow gaps give near-solid screening; slim battens with wider gaps give partial screening and more airflow. Angled fins block direct sightlines while keeping air moving.
Can the profiles be installed vertically and horizontally?
Yes. Profiles can run vertically for batten screens or horizontally for slat screens. Span between supports depends on the profile, orientation and design wind speed; use the Geolam span charts for early estimates.
Are these the same as aluminium privacy screens?
Aluminium privacy screens is the British spelling used in the UK, Australia and New Zealand. Searches for vertical aluminium privacy screens or aluminium louvre privacy screens describe the same product types this page covers. Geolam profiles have an aluminum core with a wood-look composite skin rather than a painted or printed finish.
Can Geolam profiles be used for office privacy screens?
Yes. Office privacy screens on corporate terraces, campus courtyards and lobby feature walls use the same profiles, so indoor and outdoor zones can share one wood-look finish. Check interior fire and finish requirements with the project team.
Can the profiles be used for privacy screen fencing?
Geolam profiles can be mounted on a structural post-and-rail frame designed by the project team to create privacy screen fencing along property lines, pool areas and courtyards. Geolam supplies the profiles; posts and framing come from the project team.
What colors are available?
Standard colors are Teak, Moleskin, Rosewood and Ebony. Carbon and Bilinga are special-order colors with a 90-day lead time and a 5,000 lin ft minimum. Custom colors start at 6,000 lin ft.
What lengths do the profiles come in?
Soleo, Careo, Planeo 4010 and Diameo 2018 have a standard length of 9 ft 10 in (3.0 m), with custom lengths from 7 ft to 19 ft 8 in on most profiles. The other Planeo boards and Diameo 2023 are produced in custom lengths up to 26 ft.
Is there a minimum order?
Soleo 6008, 6010, 6031 and 6033 are stocked in the USA with no minimum in Teak and Rosewood; Moleskin and Ebony in those profiles start at 1,000 lin ft. Every other profile has a 1,000 lin ft minimum in any standard color. Carbon and Bilinga start at 5,000 lin ft, and custom colors at 6,000 lin ft.
How are privacy screens maintained?
Rain usually keeps the profiles clean. For stubborn dirt, wash with warm water and mild dish soap, then rinse. Power washing is fine and does not affect the warranty. There is no staining, sealing or painting.
What does the warranty cover?
Geolam provides a 10-year non-prorated limited warranty: the profiles will not split, splinter, rot or suffer termite or fungal decay damage. It excludes color variation, normal weathering, improper installation and non-Geolam fasteners.
How do I get pricing for a privacy screen project?
Send elevations or a sketch with heights, run lengths, preferred profile, spacing and color to Geolam or your local Geolam sales representative. Pricing depends on profile size, spacing, color, length and accessories.
Ready to see it in hand?
Order a physical sample box, or get a project quote from your local Geolam representative.

